The Hollywood Racks RV Rider 2 Bike Rack for 1 Standard and 1 Fat E-Bike part # HLY64FR is the perfect option to carry one standard bike and one fat tire e-bike on the back of a 5th wheel trailer. The weight capacity for either bike is 80 lbs so there will be absolutely no issues here and in regards to tire size, one set is rated for tires up to 3" wide and the other 5" wide. The fat tire wheels hoops are installs on the inside as that is where you'll want the heaviest bike to be. view full answer...
In order to add a swinging cargo carrier to a Mercedes-Benz Sprinter you have a few options, the GearDeck 17 Enclosed Carrier part # H00604 doesn't swing away, but it does slide away. You could also consider the Yakima EXO Swing Away Enclosed Cargo Carrier - 2" Hitches - 10 cu ft - 100 lbs # Y62VR. Or, you can use any open carrier you like like the 24x60 etrailer Cargo Carrier part # e98874 along with a swing-away adapter, the Yakima BackSwing Swing Away Hitch Extender part # Y02483. view full answer...
If there is a 5th wheel hitch bracket in your 2013 Ford F-150 then you would need to remove it to install a different hitch like the Hide-A-Goose Underbed Gooseneck Trailer Hitch with Custom Installation Kit - 30,000 lbs # 9465-37 you referenced. There wasn't a factory hitch option in your truck so it is aftermarket. You do not want to grind down anything, so you will either leave it or completely remove it.
If you do have the pucks then I recommend going a different route. You can... view full answer...
The Go Power Retreat Solar Charging System part # 34272635 which is what I recommend can be used to charge two six volt batteries wires in series. In regards to installation, the positive wire from the controller goes to the open positive terminal on one battery then the negative wire from the controller goes to the open terminal on the other battery. view full answer...
I have just what you need, the Curt Ball Mount part # C45338 which has a 7" rise and is designed for a 2" trailer hitch. This is a fixed ball mount but we have adjustable options, the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount part # CAB-UM which has built-in cushioning.
If you go with the Curt Ball Mount, you'll also need the Hitch Ball part # A-90 for 2". If you go with the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount, you'll need the Convert-A-Ball Interchangeable... view full answer...
The etrailer Trailer Hitch Receiver part # e98840 is the best looking, most OEM like trailer hitch available for a 2018 Acura MDX. The etrailer hitch has a hidden design which means the cross tube is hidden and all you'll see is the required receiver tube opening. Furthermore, the receiver tube is tucked up nicely under the rear bumper so it doesn't hang down and reduce ground clearance. This is the least visible option for this vehicle. The finish on the etraler hitch is also matte which... view full answer...
The Progressive Dynamics Pure Sine Wave Inverter part # PD1210NR is just what you are looking for as it comes with a built-in transfer switch which will automatically change to shore power when available. It also comes with a wall switch which lets you control the unit while in the RV. view full answer...
I have just what you need to add airbags to a 2001 Ford E-450 Chassis (Class C Motorhome), the Air Lift LoadLifter 5000 Air Helper Springs part # AL57242 unless you have supply lines on the outside of the frame then use part # AL57131. These kits are both no-drill options which is rather rare for a motorhome. view full answer...
Yes, we have the Firestone air bag kit part # F2299 as a fit for your 2010 Dodge Ram that is perfectly compatible with the Draw Tite hitch part # 9464-35 you referenced.
For a compressor kit then the heavy duty part # F2097 will make inflating the bags and maintaining them very easy. The compressor will inflate faster than standard compressors and the gauge inside the vehicle will allow you to monitor and inflate them from inside the vehicle as well. view full answer...
Sounds like you had a massive short to ground on the 12 volt accessory circuit of the trailer wiring. This circuit is in the 1:00 position of the female connector on the truck. The ground circuit is in the position opposite of this in the 7:00 position. My guess is there was exposed wire on the trailer side between these two circuits and they touched which caused the problem.
For a new 7-way kit for the trailer you'd want the part # HS381-9000 and then for a new 7-way for the truck you'd... view full answer...
The outer tube's outer diameter of the Trailer Valet JXC Trailer Jack # TV94FR is 2-1/4 inches and the inner tube's outer diameter is 2 inches. view full answer...
Any time you are towing a fifth wheel trailer you are going to benefit from an air bag kit to give you additional suspension support. Your trailer weighing 14,000 lbs is quite a bit of weight. An air bag kit like the part # F35FV would give you a much safer and easier towing experience.
For a compressor kit then the heavy duty part # F2097 will make inflating the bags and maintaining them very easy. The compressor will inflate faster than standard compressors and the gauge inside the vehicle... view full answer...
The correct 7-way kit for your 2018 Ford F-150 that matches the rectangular connectors you sent us a picture of is the Curt part # C56413. I attached a picture our installers took that shows this connecting to same connectors. view full answer...
I looked up the owners manual for your 2019 Honda CRV FWD and in the "Towing Your Vehicle" section it states that your vehicle is not designed to be towed behind a motor home, and if you need to tow it to see the "emergency towing" section.
The emergency towing section stated that the all wheel drive models are required to be flat bed towed with all wheels off ground, and the front wheel drive models can be towed with the rear wheels on the ground.
So I called Honda directly to get... view full answer...
In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out.
Next thing you will need to know is what spindle you have on your trailer. In order to do that you can either get the inner and outer bearing numbers from a hub... view full answer...
Based on your dimensions you do need a 1 inch rise. Now that said Class I hitches you have to use only the recommended ball mount from the manufacturer would be the part # C45521. Due to the lower capacity of the Class I hitches using a longer or larger ball mount might cause excessive strain on the hitch.
For a hitch ball you'd want the # A-82 for a 2 inch ball or # A-80 for 1-7/8 inch hitch ball. view full answer...
You do not have to use a front Timbren kit when installing a rear kit like the part # TDR1500DQ on your 2012 Ram 1500. In nearly all situations where we sell Timbrens the customers are just installing a rear kit. Typically the front kits are for trucks that are using a heavy snow plow. view full answer...
If you're looking for a bike rack for your 2017 Toyota RAV4 that is not for hitches, then you will need a trunk-mounted bike rack.
The Saris Bones EX 3 Bike Rack, part # SA803, is confirmed to fit your RAV4 and can hold three bikes. It utilizes straps to mount to the hatch, making it very easy to install. I've linked to a video review of this rack for you to look at. view full answer...
To replace submersible lights, you will need to replace the entire unit because the light is sealed so bulbs are not accessible. You can use the Wesbar LED Trailer Clearance or Side Marker Light - Submersible - 1 Diode - Rectangle - Amber Lens # 47-203667 and the Wesbar LED Trailer Clearance or Side Marker Light w/ Reflector - 1 Diode - Black Base - Amber Lens # 47-222012. view full answer...
Yes we confirmed with Curt that the hitch part # 14055 that you referenced does fit your 2000 Ford E-250 extended version that has the step bumper. view full answer...
Go To Results